The acidizing spread on this truck is built around a centrifugal charge pump that moves 1000 m3/h at 45 m of head, controlled either at the panel or from a 30 m wired remote. That high-flow feed supplies the high-pressure acidizing side of the unit, where wetted parts - fluid ends, valves and manifold - are cast in acid-resistant alloy so gelled and retarded acid can be injected without the corrosion leakage that ordinary service pumps see. The same truck handles matrix acidizing, acid-fracturing placement and squeeze or circulation flushing, then a fresh-water flush routine clears the lines after the job. Mounted on an off-road chassis, it drives between wells as one load rather than being rigged from modules on location, which suits scattered cluster-well stimulation and old-workover rehab programs.
The on-board centrifugal pump is rated for 1000 m3/h against a 45 m head, sized to feed the acidizing high-pressure circuit fast enough that injection rate does not stall while the blend changes. A single pump covers both suction charging and circulation duties, so no external priming unit is called for on location.
Fluid ends, plungers, valve seats and the high-pressure manifold are machined from corrosion-resistant alloy rather than standard carbon steel, the choice that lets the truck take gelled acid, retarded acid and additive treatments without pitting or seal failure. The post-job fresh-water flush is built into the operating procedure to keep that alloy surface clean between jobs.
Operation is run from the on-board control panel, or handed to a 30 m wired remote so the operator can stand at the wellhead and watch returns while adjusting rate. That split matters on acid jobs, where pressure and rate have to be trimmed the moment the break-down response shows in the tubing.
Beyond acid injection the unit does near-wellbore scale dissolution, squeeze treatment and circulating flushing, which makes it a single asset for stimulation, damage removal and wellbore cleanup rather than a one-fluid tool. It can also work in parallel with sister units on a multi-well batch program.
Power, pumping, acid-proof manifold and control cabinet ride on one off-road chassis, so the truck arrives, connects two hoses and starts pumping instead of waiting for module assembly. Weight is balanced for road transit between scattered desert, Gobi and plateau sites.
The control platform logs injection pressure, rate and pumped volume as the job proceeds, then exports the record for the stimulation report. Closed-loop trim holds rate near target and guards against over-pressure when the formation breaks down.
| Product | Acid Pump Truck |
|---|---|
| Product line | Cementing & Fracturing Equipment |
| Centrifugal pump displacement(m3/h) | 1000 |
|---|---|
| Pumping head(m) | 45 |
| Working medium | Clear water, fracturing liquid |
| Control mode | Local / 30m wired remote |
For a useful technical response, include the target well conditions, operating depth or pressure, expected quantity, destination and any required configuration.
Send an InquiryAvailable configurations can be matched to the equipment model, operating conditions and project requirements.
The acid pump truck questions that matter most are pressure, displacement and acidizing service scope.
The Acid Pump Truck is a mobile high-pressure pumping unit dedicated for oil-gas well acidizing operations. It injects various acid fluids into target formations to dissolve plugging materials, remove formation damage and restore reservoir permeability, so as to boost well output. It also supports well flushing, squeeze treatment and pressure-test auxiliary jobs.
The pumping media includes corrosive gelled acid, retarded acid and other acidizing fluids. Special acid-resistant alloy for pump fluid ends, plungers and manifolds prevents chemical corrosion and leakage, securing equipment service life and construction safety during acid treatment jobs.
Yes. The hydraulic stepless drive trims pump speed against the downhole response, holding pressure and rate near the set point while the formation takes fluid and guarding against over-pressure at breakdown. Injection pressure, rate and pumped volume are logged on the control platform for the stimulation record, so the acid volume per stage stays consistent across matrix acidizing and acid-fracturing placement.
The unit is rated for −40 ℃ to +55 ℃ ambient duty. Optional low-temperature startup, thermal-preservation and sand-proof packages support year-round operation on plateau, desert and Gobi leases; state the site climate at order time so the cold-start and dust specification is matched.
Yes. The configuration is settled against the well program before the order: pressure and displacement rating, acid-resistant material grade for the fluid ends, explosion-proof specification, metering tank and remote monitoring package are matched to well depth, formation conditions and local oilfield safety regulations, then written into the quotation and the factory test report.
Commercial terms are confirmed in the quotation for the exact configuration, quantity and destination.
Built to API oilfield equipment standards at the Jingzhou plant under ISO 9001:2015 quality management; each acid-resistant wetted-end assembly is pressure-hold tested before dispatch and the certificate scope is listed in the quotation.
Cementing unit manuals, pump performance curves and pressure-vessel test reports are supplied; the batch mixer and manifold drawings are provided for integration with the client's cementing spread.
Confirmed in the quotation according to configuration, quantity and destination.
Manuals, conventional spare parts and remote technical guidance are included; on-site commissioning and operator training can be arranged on request.
Payment schedule, Incoterms, port and packaging are agreed in the sales contract.
A recommended spare-parts list for the first operating period is provided with the quotation.
Explore nearby products to compare equipment scope before sending an inquiry.
This truck carries two triplex plunger pumps - 3ZB-265 or 3ZB-300 units - on a Beiben ND2254F50J 6x6 chassis, each rated to put 70 MPa and a combined 100 m3/h into the casing string.
The support role on a cementing or fracturing spread is filled by this truck's centrifugal pump - 750 m3/h at 45 m of head - feeding clean water or fracturing fluid to where the active equipment is working.
A fracturing truck earns its place on location by two numbers: 105MPa maximum pressure and 2719 L/min maximum displacement.
The truck-mounted cementing range is specified by two pressure classes and two drive options.
